Forum: Third Generation
08-24-2010, 10:36 PM
|
Replies: 6
Views: 13,012
Moar pics, sorry : P
i bet u guys are getting sick of me making new posts but im trying to get past newbie status : P
anyway, got the hood back on, i LOVE this hood. i kinda want to put hood pins in it because im...
|
Forum: Electrical
08-24-2010, 10:19 PM
|
Replies: 6
Views: 12,241
|
Forum: Third Generation
08-20-2010, 12:54 AM
|
Replies: 10
Views: 19,505
|
Forum: Third Generation
08-18-2010, 11:48 PM
|
Replies: 10
Views: 19,505
Hmmm ... what to do...
Two weeks ago i got asked out by a chick for this Friday night that i have been ditching for the last couple months because i had a steady stream of car parts coming in and have been literally...
|
Forum: Third Generation
08-15-2010, 03:50 PM
|
Replies: 13
Views: 21,249
using an Edelbrock Super Victor Sr., single...
using an Edelbrock Super Victor Sr., single plane.
and no, no fuel leaks anywhere.
and yeh, my timing mark jumps around a lot, or at least a lot more than i like.
Still leaning towards picking up...
|
Forum: Third Generation
08-14-2010, 12:43 PM
|
Replies: 13
Views: 21,249
nope. distib has no vacuum adv.
im still...
nope. distib has no vacuum adv.
im still toying with the idea of shelfing the MSD stuff and putting in a HEI with a MSD module, but for next year, not this year.
Car hasnt run since 2006 so i...
|
Forum: Third Generation
08-14-2010, 04:05 AM
|
Replies: 13
Views: 21,249
|
Forum: Third Generation
08-13-2010, 06:34 PM
|
Replies: 13
Views: 21,249
well. did a compression check on the passenger...
well. did a compression check on the passenger side cylinders and No.1, 180 - 190 average for each, i then jus spun the motor over and looked at the rockers and all of them had full range of motion....
|
Forum: Third Generation
08-13-2010, 01:16 PM
|
Replies: 13
Views: 21,249
im starting to think, with my luck, i have an...
im starting to think, with my luck, i have an exhaust cam lobe go bad already. gonna try to check that next. if that turns out to be true, ... that will suk. cost me another 250$ to fix that. i...
|
Forum: Third Generation
08-13-2010, 04:21 AM
|
Replies: 13
Views: 21,249
|
Forum: Third Generation
08-13-2010, 01:57 AM
|
Replies: 13
Views: 21,249
I knew it was too good to be true
well. i got a drive shaft and had it shortened, cost about 75$ more than i was expecting but whatever.
had started the motor for about a minute, set the timing, sounded great. no alternator...
|
Forum: Third Generation
08-08-2010, 02:39 AM
|
Replies: 3
Views: 10,382
|
Forum: Third Generation
08-08-2010, 01:34 AM
|
Replies: 3
Views: 10,382
700R4 / TH350 crossmember massage
spent a few hours futzing around with the cross members today.
Problem: the cross member i was using that is meant to be used with the PA Racing torque arm i have was in the way of my 3" exhaust...
|
Forum: Third Generation
08-03-2010, 07:43 PM
|
Replies: 3
Views: 10,169
Houston, we have ignition!
turns out when i put in the distributor i was 180* out. Set it back in correctly this time, put the crank about 12* BTDC, rotated the distributor to where approx. where the rotor was pointed [about 5...
|
Forum: Third Generation
08-03-2010, 04:40 PM
|
Replies: 19
Views: 21,289
|
Forum: Third Generation
08-03-2010, 03:10 PM
|
Replies: 19
Views: 21,289
|
Forum: Third Generation
08-03-2010, 03:26 AM
|
Replies: 19
Views: 21,289
|
Forum: Third Generation
08-02-2010, 06:26 PM
|
Replies: 19
Views: 21,289
just to make sure we are on the same page, you...
just to make sure we are on the same page, you got one WHAT exactly?
a drive shaft? how long is it? i need one atleast 5 or 6" longer than my stock drive shaft, and how are you measuring it? ive...
|
Forum: Third Generation
08-01-2010, 03:41 PM
|
Replies: 19
Views: 21,289
hmmm..... ok.
I had 1 buddy send me a link...
hmmm..... ok.
I had 1 buddy send me a link for a coil [4 or 5 feet] of 3/16" teflon vacuum line, so i ordered that.
sure enough, the next day im out looking for 3/8" aluminum fuel line and i...
|
Forum: Third Generation
07-29-2010, 03:12 AM
|
Replies: 16
Views: 16,680
well. i like both of those.
might be able to...
well. i like both of those.
might be able to afford one next year though.
right now i still need to buy 2 front tires for my new 15x4 rims and still have to get the drive shaft altered.
there is...
|
Forum: Third Generation
07-28-2010, 11:22 AM
|
Replies: 16
Views: 16,680
|
Forum: Third Generation
07-27-2010, 10:26 PM
|
Replies: 16
Views: 16,680
So....
i got the TH350 installed...
and what do you think is staring at me on my work bench?
|
Forum: Third Generation
07-26-2010, 04:58 PM
|
Replies: 19
Views: 21,289
|
Forum: Third Generation
07-25-2010, 06:48 PM
|
Replies: 19
Views: 21,289
torque arm is not an issue, im using S&W SFCs...
torque arm is not an issue, im using S&W SFCs that has its own toque arm mount and drive shaft loop.
yes im aware i have to have my drive shaft lengthened, hopefully in the next couple weeks.
im...
|
Forum: Third Generation
07-25-2010, 01:40 AM
|
Replies: 19
Views: 21,289
TH350 steel vacuum line?
well. i ended up 86'ing the 700R4 and im in the process of trying to install a TH350. if anyone else has done this, got any tips/suggestions? im stuck right now trying to figure out if i can pick up...
|