|
#21
05-01-2016, 07:10 PM
|
||||
|
||||
Stainless tank in, Fuel pump plumbed and wired. Vacum pump in and wired.
Now waiting on the radiator 4 row aluminum BBC. I wired the fuel pump with relay and trigger switch off the oil pressure switch. Lose Oil pressure and pump turns off. almost done with grill too!
__________________
 "As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen US NAVY RETIRED 
|
|
#22
05-07-2016, 09:20 PM
|
||||
|
||||
|
the stainless tank.
 the fuel pump setup I fabbed.  New 4 row BBC radiator (outta keep it Cool)  engine pretty much Completed, just some odds and ends to take care of.  run after initail tune.
__________________
"As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen US NAVY RETIRED
|
|
#24
05-08-2016, 12:30 PM
|
||||
|
||||
|
Looking and sounding good Dawg!!!
__________________
 68 Camaro (?350 SB) 69 Camaro (L72 427 BB) 69 Camaro (DZ 302 SB - www.z28.net) Camaro - A friendly flying car – from the French - the first half "camarade/friend" and the last half “aero/of the air".
|
|
#25
05-09-2016, 03:31 AM
|
||||
|
||||
|
sounds. needs more timing at idle. too bad your stuck with carb and dizzy. its nice to have 28 degrees timing at idle. To then have is smoothly drop down and sweep back in at WOT
__________________
 1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore.  BAAAAAA!!!!!!
|
|
#26
05-09-2016, 10:50 AM
|
||||
|
||||
|
what I need is a power valve idle mixture has no effect and I'm pullin 7" at idle.
I got an 8.5 pv in there now I need a 3.5. timing set to 34* @ 3500 rpm and 12* at idle (set to builders recommendations). It will run much better with the proper power valve.
__________________
"As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen US NAVY RETIRED
|
|
#27
05-09-2016, 12:32 PM
|
||||
|
||||
|
that much cam and cubes and 12 degrees? try it. lock the dizzy at say 27ish. will clean up the idle.
__________________
1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. BAAAAAA!!!!!!
|
|
#28
05-09-2016, 04:14 PM
|
||||
|
||||
|
ill play with it after I get the proper power valve .
__________________
"As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen US NAVY RETIRED
|
|
#29
05-10-2016, 01:55 AM
|
||||
|
||||
|
power valve wont effect idle, tuning for idle quality can be done still. just an FYI.
http://www.corvetteforum.com/forums/...gine-idle.html
__________________
1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. BAAAAAA!!!!!!
|
|
#30
05-10-2016, 10:35 AM
|
||||
|
||||
|
thanks for the link and advice Pizza Ill try that but I must first follow the builders recommendations first due to the engine being under warranty.
__________________
"As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen US NAVY RETIRED
|
 |
|
|
Linear Mode
