#31
|
||||
|
||||
spark plugs, dist cap, rotor, injectors, and plug wires are in and no misfires and no stumbling at low rpms.
I took the bed off today and have to replace the fuel sending unit and figure out what the heck to do with the rusty frame. I'm not looking for pretty, just something to stop the cancer known as rust. I have read so much crap on POR...pros and cons...that I'm not sure what to do. I just want something fairly easy that will stop the rust. If anybody has any suggestions....I'm listening. taking the bed off a forklift really helps...lol. i hate rust...go with por15?
__________________
68 Camaro (?350 SB) 69 Camaro (L72 427 BB) 69 Camaro (DZ 302 SB - www.z28.net) Camaro - A friendly flying car – from the French - the first half "camarade/friend" and the last half “aero/of the air". |
#32
|
||||
|
||||
I like por but since it is a plow truck i would get the brush on bed liner shit and do the metal with that nothing will get theough thar shit lol
__________________
2000 SS Procharger 98 Z vert turbo 07 TB SS cai catback and tune |
#33
|
||||
|
||||
Quote:
Rust reformer http://www.amazon.com/Rust-Oleum-783...=Rust+Reformer bed liner: http://www.amazon.com/gp/product/B00...k_ql_qh_dp_hza
__________________
68 Camaro (?350 SB) 69 Camaro (L72 427 BB) 69 Camaro (DZ 302 SB - www.z28.net) Camaro - A friendly flying car – from the French - the first half "camarade/friend" and the last half “aero/of the air". |
#34
|
||||
|
||||
The gas gauge problem is definitely the sender.
I put an ohmmeter directly across the two wires where there is the moving contact along the resistor. When the float moves, the resistance just jumps around between a real high resistance and 0 ohms. Oh well....it's been replaced and is working good now.
__________________
68 Camaro (?350 SB) 69 Camaro (L72 427 BB) 69 Camaro (DZ 302 SB - www.z28.net) Camaro - A friendly flying car – from the French - the first half "camarade/friend" and the last half “aero/of the air". |
#35
|
||||
|
||||
Today sucked.
Herculiner does not stick to rust. Had to go the POR-15 route. Over the past few days, I read the instructions and did all the steps. Degreaser, then Metal Prep and then let it dry out for 24 hours. This morning was POR-15 paint day with the truck outside. I had on grungy pants, a long shirt, face mask and long gloves. About 1/2 way through painting, my glasses started sliding off and I reached under the mask and pushed them up and then kept on painting. I looked in the mirror about an hour later and I had POR-15 all over my nose. There is no good way to take this crap off. I read everything online and gas, kerosene, lacquer thinner, etc do not work. I scraped my nose until it was red, raw and bleeding. Going into work with a weird shaving accident (lol) >> than going into work with a black nose. Yep. Today sucked.
__________________
68 Camaro (?350 SB) 69 Camaro (L72 427 BB) 69 Camaro (DZ 302 SB - www.z28.net) Camaro - A friendly flying car – from the French - the first half "camarade/friend" and the last half “aero/of the air". |
Thread Tools | |
Display Modes | |
|
|