North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Racing (http://www.northeastf-bodyassn.com/forumdisplay.php?f=28)
-   -   Ran with the New 410's (http://www.northeastf-bodyassn.com/showthread.php?t=3246)

Camaro9969 09-01-2011 03:16 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 54823)
Nice! Yeah you should be right around high 11's low 12's with that trap speed. Its all seat time. Good job so far. You will see 11's before the seasons over. Just practice on the street 1-2 shift as fast as you possibly can without breaking anything. Cut down on your time shifting and you should catch it.!

Thanks man ya the 1.76 was a great 60ft i was happy, too bad i had her in the car lol my 60 was great and the 1/8th was perfect i was trying to run over a 13.9 so i didnt use 4th jammed the brakes and still did 13.0 haha killed the mustang in the other lane still!!!

Camaro9969 09-01-2011 03:18 PM

Quote:

Originally Posted by SLP IROC-Z (Post 54611)
ok just watchd the videos, back in the water and do a quick dump in 2nd to get them wet, pull up out of the water box and do a 2nd gear burnout at 5000 to 5500 rpms for a good 5 seconds then ride it out for a few feet. doing the burnout in the water poses two problems, the tires not drying off completely and the shock load from spinning the tires on wet ground and then hitting dry sticky concrete, this is a sure fired way to grenade a 10 bolt.

i can tell youre shifting way to early just from where you are on the track when you shift.
watch me race the gtp in the end of this video http://youtu.be/oLfJipqLlsI
my engine is 100% stock, and i shift just shy of my 6200 limiter, pay close attention to where each of my shift points are on the track. youre shifting 1-2 right at the 60' mark, thats way before 6k rpm. not only will that hurt your 60' but its going to slow your runs way down. im running a stock tach and no shift light, but after hitting the rev limiter a few times before a shift i got an idea of where my rpms were and were to shift the car at. with a 6500rpm shift point you should be over 100' out before youre into 2nd gear.

That idiot on LStech is starting again with his stupid DA shit haha hes obnixous

SLP IROC-Z 09-01-2011 05:04 PM

7.89 1/8T @ 93, that was an 11

SLP IROC-Z 09-01-2011 05:07 PM

Quote:

Originally Posted by Camaro9969 (Post 54825)
That idiot on LStech is starting again with his stupid DA shit haha hes obnixous

oh jesus, that kids the definition of face palm.

Camaro9969 09-01-2011 07:56 PM

Quote:

Originally Posted by SLP IROC-Z (Post 54834)
oh jesus, that kids the definition of face palm.

hahaha ya he is!!!

Camaro9969 09-01-2011 07:58 PM

Quote:

Originally Posted by SLP IROC-Z (Post 54833)
7.89 1/8T @ 93, that was an 11

I figured it was a good run. Felt fast. I dropped more air out and got way better traction i pretty much dumped it at 5 grand and spun hard so i dropped more air hammered it and it spun only a little but leaving very hard. Theres still time and according to the "know it all" i'll have to wait till January to run 11's!!!!!!

Formula413 09-01-2011 10:09 PM

Me and Fastass Joe were gonna come up but he got stuck at work and I didn't feel like going by myself. Probably gonna run my car once before the season ends, shooting for a Wednesday this month.

Where's the thread on LS1Tech? There's some serious hammerheads over there for sure LOL

*LS1* Queen 09-01-2011 10:29 PM

http://ls1tech.com/forums/12-second-...-new-410s.html
funny cause the guy kept deleting his posts but they were already quoted lol...guys a real winner and the thread is keeping me amused haha

oh and congrats...ull def get it into the 11s soon...good luck!

Camaro9969 09-01-2011 10:36 PM

Quote:

Originally Posted by Formula413 (Post 54843)
Me and Fastass Joe were gonna come up but he got stuck at work and I didn't feel like going by myself. Probably gonna run my car once before the season ends, shooting for a Wednesday this month.

Where's the thread on LS1Tech? There's some serious hammerheads over there for sure LOL

Fatass? That's not nice lol. You shoulda just came up with me. I'm gonna go either this saturday or next wednesday again we all could do a Saturday morning that would be cool . The best part of the night was a guy asking what rear end it was because i launched the shit out of it and no way a 10 bolt could hold lol well it has.......for now anyways

Camaro9969 09-01-2011 10:39 PM

Quote:

Originally Posted by *LS1* Queen (Post 54849)
http://ls1tech.com/forums/12-second-...-new-410s.html
funny cause the guy kept deleting his posts but they were already quoted lol...guys a real winner and the thread is keeping me amused haha

oh and congrats...ull def get it into the 11s soon...good luck!

I was wondering where his comments were going. He deleted them? Even more reason the guy is a tool!!! That is really pissing me off I like how joe just keeps making fun of him .... And thanks hopefully will one night. I just want to do it soon before I start building my turbo project

smokinss 09-02-2011 12:29 AM

Your def getting there man. I started the same way and my wife telling me I need to shift faster. Haha. But save up for a good rear and tires and some more seat time. You will see a big improvement.

This was my car before I went to a auto but launching with built rear and good slicks makes a huge difference.

http://www.youtube.com/watch?v=8BEPKM7UKKg

Camaro9969 09-02-2011 12:50 AM

Quote:

Originally Posted by smokinss (Post 54864)
Your def getting there man. I started the same way and my wife telling me I need to shift faster. Haha. But save up for a good rear and tires and some more seat time. You will see a big improvement.

This was my car before I went to a auto but launching with built rear and good slicks makes a huge difference.

http://www.youtube.com/watch?v=8BEPKM7UKKg

Oh i've seen that video many times!! hahaha That car is incredible. you were launching with a 150 shot??? Ya a real rear end will do the trick but this winter is a serious project for me lq9 Turbo and a ford 9" (and cant decide if i want to keep a 6 speed or a auto) Either way your camaro is sick where were you running that said palm beach? haha I bought this car completely stock last march and my first run was a 13.7 and a few 14's then have ran like 30 runs total its fun to see the times go lower and lower....

smokinss 09-02-2011 11:01 AM

I would love to go turbo in my ss but not to sure about funds. And yeah I live down here in florida. The track is about a 40min drive from me. I will say a stalled auto is def pretty fun. Especially when it has a manual valve body in it.

Camaro9969 09-02-2011 03:35 PM

Quote:

Originally Posted by smokinss (Post 54882)
I would love to go turbo in my ss but not to sure about funds. And yeah I live down here in florida. The track is about a 40min drive from me. I will say a stalled auto is def pretty fun. Especially when it has a manual valve body in it.

When you ran a 10.97 was that a LS1 cam only with a 150 shot?

smokinss 09-02-2011 05:42 PM

Yeah pretty much. Cam bolt ons,built driveline and a 150 hit. All on a 140k stock bottom end

Camaro9969 09-02-2011 07:50 PM

Thats unreal i'm sure the transmission was built up haha....stock heads? its almost not worth doing a whole motor swap considering ill be spending 5x as much and gaining maybe a second less that a 10.97

My84Z 09-02-2011 08:01 PM

Yeah bua built motor will do those times n/a and you get reliability with a built motor not a cold sweat wondring if this is the pass the bottom end let's go lol

smokinss 09-02-2011 10:12 PM

Well put Jon. That's why next on my list to at the very least forge my bottom end and through the 200 at it.. And yes that was with stock 853 casting heads, and race weight of 3730 with me in it. That run had a 1.58 60'. I went a 1.52 on a diifferent night but missed 3rd. Doh!!!!!

Camaro9969 09-02-2011 10:14 PM

Ya your right i will be nervous everytime i hammer it down the track with my motor, i already have 128k on it and it was babied until it came to me last year and those are some rough miles lately! What have you ran with the auto now?

smokinss 09-03-2011 11:50 AM

Yeah my bottom end is at 143k and has been sprayed since 55k when I bought it. Lol

I haven run yet with the auto. I will know on the 21st what she does. Its still kindaa hot down here but I am hoping for 10.5s in good air.

Camaro9969 09-03-2011 12:20 PM

Holy Shit that many miles since spray? Haha I should just spray mine just till the end of the year

ILuvPizzaTimes10 09-03-2011 03:17 PM

It might last. Or something could go wrong and boom. I like the idea of spray easy cheep power. But it goes wrong your at the least out an intake or worse. That's just me. You gotta see both sides of it. One guy has great luck the next guy spins a rod bearing yah just never know.

smokinss 09-03-2011 10:03 PM

Yeah but look at all the shit you have broke on your built lt1 and that's without spraying it. Also boost can be just as bad with the wrong tune up. No matter which way you go you take the chance of breaking shit. Alot of people give nitrous a bad name, me personally I've got no issues at all with it. If done properly its still a fairly cheep power adder.

Slowhawk 09-04-2011 01:17 AM

Watch out spraying with that tranny swap. An auto has a much higher fuel demand.

Camaro9969 09-17-2011 11:58 PM

Updated Time Slip. Damn close to that 11.99 that i want with this set up. I think i'll get it a few times just launched it pretty hard today. Very good 60ft time. Second run of the day almost got smashed into i'll post video when i get it up. But no clue how she did it but she was in the left lane and flew into mine and hit the wall hard! Her dad said she was just learning. Ouch!

Anyways heres the slip
http://i39.photobucket.com/albums/e1...1/IMAG0021.jpg

ls6monte 09-18-2011 12:16 AM

Nice! Almost there!!

Camaro9969 09-18-2011 01:08 AM

Oh ya and i also weighed it at 3710 with me in it. haha

Formula413 09-18-2011 01:24 AM

Damn, almost there. That is a porky car huh? My Formula was 3600 lbs with me and a quarter tank on that same scale! It might just need a little dieting to run 11s.

SLP IROC-Z 09-18-2011 05:25 AM

there ya go man, thats a nice slip!

Camaro9969 09-18-2011 10:56 AM

Thanks guys ya i was impressed with the 60ft. I held it at 4 grand and let it rip. I figured it would blow the rear end but not that time. Actualy i was wrong it was 3610 w me in it. Sorry i just looked again at the print out he gave me. still heavy and i took everything out pretty much that i could. Oh one issue i ran into during the day was the harder i launched it the less likely it was to go into second gear smooth. The first one it grinded so bad it took a second or two to get it in there. So i went in and bled the clutch out a ton to get some new fluid in. This run it still grinded but not much. Everything is new but i'll make sure that is bled a ton before i race next time i would like a smooth 1-2 shift that doesnt help at all

smokinss 09-18-2011 12:03 PM

Nice slip man. See, your getting there. Is the tranny built or not?

Camaro9969 09-18-2011 01:35 PM

Quote:

Originally Posted by smokinss (Post 55778)
Nice slip man. See, your getting there. Is the tranny built or not?

Thanks man. Its a stock tranny with a Monster Stage 3 clutch. Second gear prob is going thats why it grinds just thought it was weird that the harder i launched the worse second was. Heres the run my sister was filming it and couldnt figure out the video but at least she got the launch. and i beat that car next to me with the slicks on it haha

http://youtu.be/Q2HycDTMZW0

smokinss 09-18-2011 02:14 PM

Yeah well what happens is there so much twisting force and torque it takes its toll. My car when it was a m6 used to do the same thing just not the full grinding. I would come out at 6k and the shift to 2nd would be a little tough.

SLP IROC-Z 09-18-2011 03:11 PM

2nd gear is weak in the pre 2000 trannies. you have a new slave and master right?

Camaro9969 09-18-2011 06:07 PM

Yes new slave and master. When i bled it it definitely got better but was in no way a smooth shift haha. The first one I couldn't even get it into second. Ill bled it with better fluid next time see what happens.

Camaro9969 09-18-2011 06:08 PM

It shifts great at high rpms unless I had a hard launch with the drag radials

Camaro9969 09-18-2011 06:22 PM

Here's the crash video haha

https://www.youtube.com/watch?v=ZWjQ...e_gdata_player

My84Z 09-18-2011 06:24 PM

Damn! Good thing you didn't let off!

Camaro9969 09-18-2011 06:30 PM

I know i looked back and was like what the fuck? Haha that could of been worse. She totaled her dads nice Nova

ls6monte 09-18-2011 10:38 PM

Should have given her a hyundai to race! NOT a Nova!


All times are GMT. The time now is 04:23 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.