North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   LSX Powertrain (http://www.northeastf-bodyassn.com/forumdisplay.php?f=37)
-   -   Intake ideas? MAF Questions too. (again) (http://www.northeastf-bodyassn.com/showthread.php?t=2245)

Batman 02-08-2011 01:12 AM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 38333)
ive seen more cars make power with AFR then TFS lately. the fast as cast is a joke and id take AFR over an out of the box TFS head.

Agreed, but TFS kills them in the low and mid range which would be preferable for a car mostly driven on the street, IMO anyway. Once again you throw peak dyno numbers in the garbage with the other numbers, in the scheme of thing they only tell you part of the story. I don't care if the car makes 50 more HP at peak RPM if the "lesser" heads make more power across 80% of the RPM range then the only place you are really gonna see an advantage with the higher HP number is on the racetrack, and chances are it will be a negligible difference. I will take bigger low/mid range numbers over peak HP any day of the week in any application except a pure track car

Bayer-Z28 02-08-2011 01:20 AM

^ This is why I research stuff.. :D Peak numbers don't mean as much to me. I look at lot at the mid-lift and middle of the powerband numbers. My buddy has an MS4 with PRC heads and he swears by it, but I pulled on him even though he made more power than I did. I've driven it and I don't care for it as a street cam. I've noticed that TR seems to pay more attention to all around performance and TSP seems to be just peak power. I figured that out a couple years ago.

The TFS also runs a lower valve angle which can also help run a different range of cams due to a slightly less risk of PTV clearance.

Slowhawk 02-08-2011 01:31 AM

I won't buy AFR heads anymore. Build quality sucks. We mostly prefer to use TEA/TFS heads. They always outperform AFR,ported TSP heads ect.

84ta406 02-08-2011 07:05 AM

Quote:

Originally Posted by Batman (Post 38336)
Agreed, but TFS kills them in the low and mid range which would be preferable for a car mostly driven on the street, IMO anyway. Once again you throw peak dyno numbers in the garbage with the other numbers, in the scheme of thing they only tell you part of the story. I don't care if the car makes 50 more HP at peak RPM if the "lesser" heads make more power across 80% of the RPM range then the only place you are really gonna see an advantage with the higher HP number is on the racetrack, and chances are it will be a negligible difference. I will take bigger low/mid range numbers over peak HP any day of the week in any application except a pure track car

Greater AVG. power > Peak power with a lower average IMO as well. I dont know all this LSx crap but I will say if you go to the track, you wont see many AFR headed cars. Brodix FTW! lol

Bayer-Z28 02-09-2011 12:32 AM

I'm torn.

I've seen all the data and I'm just still worried about losing low end on the 102. I've got the money to buy it now. Just last minute jitters, I guess.

Batman 02-09-2011 02:17 AM

I think the 92 or 90 would be a better fit for you if you can get your hands on one.

Formula413 02-09-2011 02:36 AM

Between the bad things I've heard about the 102 and just the fact that it's huge and your motor is stock cubes and not too radical a cam it doesn't seem like a good fit to me. Have you heard good things about it in your research?

Batman 02-09-2011 02:41 AM

I would almost go LS6 or an LS2 intake over a 102.

Bayer-Z28 02-09-2011 03:14 AM

^ The LS6 outperforms the LS2. LS2 is a turd compared to the 6 and 3. The TB size doesn't make the intake and has little to do with it. I've learned a LOT this week.. :)
As I see it, the 102 is almost an ITB intake wrapped in polymer/plastic.


Check it.. This settles it.

Quote:

Originally Posted by Tony Mamo @ AFR (Post 14476527)
OK...this thread is pretty funny talking about nothing....LOL

Guys...

When we are discussing fuel injected applications.....the size of the plenum and the opening or the TB (size) will have zero effect on "low end" power.

This is old school thinking stemming from the very real and often practiced applications where too large a carb might have been bolted on a particular engine combination.

The problem stemming from the fact the large carb slowed the airspeed down enough in the venturi's of the main body to negatively effect the carb atomization and therefore hurt power, torque, fuel economy, and responsiveness until enough RPM was generated to allow the carb to become more effective again (guys older than 45 will be nodding their heads up and down right now while reading this!).

We aren't atomizing fuel here folks....thats handled by the injectors and the real meat and potatoes of manifold design (runner length, shape, and taper) hasn't changed much from the 90, 92 or 102.....its very similar but the 102 does have a superior shaped runner (although the length is very similar), is slightly taller, and ultimately flows more, especially when properly ported.

Yes....a FAST 102 can flow more than a 280 CFM head but thats always the case with a really good intake....ideally you want ALOT of headroom when selecting a manifold so when you bolt it in front of your heads it flows more net to the cylinder with the ultimate situation to not hurt the port any more than placing a radius plate in front of it. Thats pure theory unless we are discussing extremely optimized straight shot tunnel ram style manifolds.

I can port a Gen I single plane intake and make it flow 400 CFM.....when you place it in front of a 300 CFM intake port that port still loses 20 CFM which is very good all thing considered. Take the same intake unported by me that still flows way more out of the box than the 300 CFM intake port in question (say the intake flows 360 CFM out of the box) and now you may only see 265 CFM when placed in front of the head because it hurt the net flow more.

INTERNET MYTH #1 .....My 102 Fast is too big for my 346

Wrong....its a better designed intake thats going to allow more air to pass thru the intake ports and be mixed with more precisely atomized fuel from your injectors.

INTERNET MYTH #2....Its already big....you dont need to port it (or it might hurt the bottom end).

Also wrong....at least when ported properly. Once again it simply makes a good piece even better but I would be the first to admit that on a marginal set of head the gains from the work would be less as well. The better the heads, the more aggressive the RPM, displacement, etc. the more that ported 102 is going to pay you in spades.

The larger the restriction the intake manifold becomes....the better your results will be when you swap to the better intake.

If your still questioning anything lets get it handled now and please refer other people back to the answers when we see the same questions and bad information in other threads....I wish I had a nickel for the guys convinced their inaccurate theories are accurate....LOL

The ONLY potential negative to the 102 design...well besides the cost of admission with the rails etc.....is the TB (airblade) is so large it can create drivability challanges with the tune but its a much easier deal on a cable operated 102 with an IAC motor. ALso, it tends to be extremely responsive which I personally like, however some have complained its too responsive (on/off) and they have to get used to driving it. No big deal in my book....

Hope this helps!

-Tony


ILuvPizzaTimes10 02-09-2011 03:44 AM

i dont agree with that completely. larger intake runners on an engine say at at low rpm and low vacuum. the air can stall in the ports. too big a plenum on a small displacement engine spinning at low rpm/high load will stall air inside the plenum. i mean believe what you wwant. real world is real world not some engine dyno/chassis dyno and the car made 40 more rwhp but ran 3 tenths slower...... i mean get it if you wish. if you choose to believe a guy who ultimatly is a sales man for FAST. of course he's going to tell you its great. and you wont lose anything. there are back to back tests on this i believe hot rod did it and the 102 lost everywere but peak over the 92/92 setup SAME 92mm tb. if i read it right.


All times are GMT. The time now is 10:30 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.