North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   LT1/TPI/TBI (http://www.northeastf-bodyassn.com/forumdisplay.php?f=36)
-   -   OK f this car NO START (http://www.northeastf-bodyassn.com/showthread.php?t=3313)

ZFreie 09-24-2011 06:34 PM

ewwwww

ILuvPizzaTimes10 09-24-2011 07:43 PM

and there it is! clean i all off with a good no flash contact cleaner and it should be all set as long as you dont see any carbon tracking on the cap.

KLAB 09-27-2011 02:30 AM

Pics of this Saturday's dissection:

I took apart my opti, cleaned the small amount of oil in it. swapped the optical sensor with that of my spare working opti, and put it all back together cleaned. it started. then turned off and no start again. :(

No leak on the timing cover to the opti
http://i99.photobucket.com/albums/l3...s/IMAG1210.jpg

I replaced these rubber o-rings on the opti shaft, as the factory service manual says to do.
http://i99.photobucket.com/albums/l3...s/IMAG1208.jpg

Only source of leaky oil on the front cover, the water pump drive seal out the timing cover. I think small amounts land on the opti and seep their way inside. BTW the opti isn't a perfectly sealed device...
http://i99.photobucket.com/albums/l3...s/IMAG1213.jpg

Common rotor wear. (spark is not the issue anyways, just a cool pic)
http://i99.photobucket.com/albums/l3...s/IMAG1216.jpg

KLAB 09-27-2011 02:38 AM

Notice lack of oil, not what I was expecting...
http://i99.photobucket.com/albums/l3...s/IMAG1218.jpg

When I saw this, I shit bricks. This HAD to be it. Oil on the optical sensor.
http://i99.photobucket.com/albums/l3...s/IMAG1219.jpg

Some splatter. Maybe it leaked a little through the shaft? But there was no oil around the seal.
http://i99.photobucket.com/albums/l3...s/IMAG1225.jpg

I didn't bother to clean this. I knew the optical sensor worked in my test unit.
http://i99.photobucket.com/albums/l3...s/IMAG1226.jpg

So we swapped em
http://i99.photobucket.com/albums/l3...s/IMAG1228.jpg

Cleaned everything
http://i99.photobucket.com/albums/l3...s/IMAG1229.jpg

KLAB 09-27-2011 02:41 AM

Ladies and gentlemen a KLaBz28 rebuilt opti:
http://i99.photobucket.com/albums/l3...s/IMAG1230.jpg

http://i99.photobucket.com/albums/l3...s/IMAG1231.jpg

She's beautiful
http://i99.photobucket.com/albums/l3...s/IMAG1232.jpg

and the startup vid. I thought I did it!!!! I jinxed myself....
http://i99.photobucket.com/albums/l3..._VIDEO0119.jpg

Then I tried to start it again and it was dead....

:klab:

KLAB 09-27-2011 03:07 AM

I have read something tonight, that leads me to go test wire B3 out of the PCM tomorrow. My brain is packed full with circuitry of this car, what goes where what does what figuring the exact algorithm process that takes place when the car is started, along with all my strengths of materials studies and labs, and BS sociology work. My head is going to pop time for sleep.

SLP IROC-Z 09-27-2011 11:29 AM

Quote:

Originally Posted by KLAB (Post 56085)

id replace any connector/pigtails that are soaked in oil. believe it or not we replace alot of pigtails on the diesels from oil contamination, it causes issues!

KLAB 09-27-2011 03:20 PM

I already tried this^ Cleaned it well and also tried swapping 2 other non oily harnesses I have, no effect. So last nigh I unplugged the opti at the manifold (up top connector) and plugged it back in with the key on. I heard all kinds of shit make noise. Beeps clicks relays on/off and the pump. Strange, I think it juiced the injectos when I did this because after that I got a sputter on start. Plugged it in and out a few times and it started... I need to borrow a noid light again today and see whats goig on.

ZFreie 09-27-2011 03:23 PM

Quote:

Originally Posted by KLAB (Post 56234)
I already tried this^ Cleaned it well and also tried swapping 2 other non oily harnesses I have, no effect. So last nigh I unplugged the opti at the manifold (up top connector) and plugged it back in with the key on. I heard all kinds of shit make noise. Beeps clicks relays on/off and the pump. Strange, I think it juiced the injectos when I did this because after that I got a sputter on start. Plugged it in and out a few times and it started... I need to borrow a noid light again today and see whats goig on.

That makes it sound like a bad wire in the whole opti harness, thats the first thing I thought anyway.

KLAB 09-27-2011 03:40 PM

Harness from the connector at the passenger side of intake manifold to the opti is good. Im checking the wirefrom PCM to the opti todayyyyayayayayyayyayayay


All times are GMT. The time now is 02:08 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.