Tested 102mm setup on my car
Put on the 102mm setup,ported with 102mm TB and 102mm Lid. Car picked up 20ft/lbs of torque from 3k to 5krpm and 10-15hp at the same area's. The Super Victor setup was evan or above in the higher rpm area's.
As for the cars response. Car ran perfect with the Super Victor then ran like Garbage with the FAST.I did some tuning but the FAST would surge bad at idle(probly due to my cam at 106IC) So the Super Victor went back on for now.I've got some more Cam testing to do. Off the top of my head the #'s were FAST - 526hp/504tq Super Victor -549hp/495tq. I figure it would be 580-590hp on my old dynojet setup. |
So the FAST just didnt cut it? i kinda figured it wouldnt. funny how it didnt make THAT much less power. so what else can be done for the running issue? and if it ramn fine and had the little bit of peak hp loss would you have kept it?
|
Quote:
|
sounds like a good little test! must be nice having a test car to figure all this shit out. now if some one comes in and goes HEY how will this setup work you can say SHITTY unless you get this cam!
|
We tested all the basic cams years ago on a few cars.Saturday Cam swaps were the norm.Got it down to 1.5hr's to do.
Yesterday it took us about 4 hours to fit the 102 setup. Got fed up on the dyno and switched back to the SV. The dyno runs were 45 minutes inbetween the intake swaps. Was running the dyno at 9pm last night with the cutout open. |
Quote:
|
haha that must have been quiet ;) cant wait to see the red rocket at the track again don
|
Quote:
|
thats awesome at cops up this way would flip
|
Do you think with a cam designed to produce a stronger midrange you could make enough power there to offset the higher RPM power loss? Then you can lose your "big and gay" hood :haha:
How does the stock LS7 intake manage to keep a 427 breathing good without being huge? |
its not a ported headed huge cammed 430ci motor. but a mild idle cam minor head worked motor that shouldnt require the air the motor don built does. is what im gathering.
|
Yeah Pizzas right about that one.
Anyway sounds like you been doing some serious testing with the redrocket. Keep us updated |
LS7 = 500HP+ at the flywheel
Don = 500HP+ at the rear wheel BIG difference |
LS7's make about 440-450rwhp on my dyno.
|
I have NO idea why FAST is now discontinuing the 92 intakes and only producing and selling the 102. I was always under the impression that the 102 is for the larger displacement engines such as the LS7, TBSS and maybe the LS3's. This isn't the first time I've heard a 102 swap running like crap. IMO, I'd put an 92mm TB on the 102 and see how it goes. The 102 is way too big for the smaller displacement engines. Also heard that you loose port velocity at lower RPM's do to having such a big mouth on that intake.
|
thats all fine and good for a 346 bayer. but if your referring to Slowhawks running like crap.... its a C5R 427.......
|
^ That's why I didn't mention HIS setup as I didn't know what it was.. It's odd that the 427 wouldn't perform well with the 102. Possibly too big of a mouth on the intake. I'd stick a 92mm TB on it and see how it runs.
I've always thought the Nick Williams intakes were puRe secks!! :D |
Don have you had a chance to dyno any cars with the Edelbrock Xt EFI intake
this one http://www.gmhightechperformance.com...smissions.html |
i was thinking about that one too. but i also read up it doesnt fit the F-Buckets. too tall for even a cowl cut in the back unless you shave the whole cowl completely off.
|
^ I've seen a GMPP EFI intake with an elbow and stock TB on tech a couple weeks ago.. I'll see if I can find it. I'd really just love a FAST 92 and call it good, but I'm researching my options as well.
-=EDIT=- here we go.. http://www.ls1tech.com/forums/genera...-big-pics.html |
| All times are GMT. The time now is 07:00 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.