North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   LT1/TPI/TBI (http://www.northeastf-bodyassn.com/forumdisplay.php?f=36)
-   -   Z won't idle? No codes... (http://www.northeastf-bodyassn.com/showthread.php?t=1633)

bottledbird68 08-24-2010 10:08 PM

Z won't idle? No codes...
 
Ok, haven't even popped the hood yet but I have a few minutes to kill between coats of paint so figured I'd post up.

Hopped in the z to go pick up a couple things. Car ran fine when we parked it a couple days ago. Starts fine, runs ok going down the road, just won't idle on it's own. Idles fine at whatever rpm I keep my foot at though.
It's not throwing any codes. Any ideas? I'll double check the intake track make sure it's tight but beyond that what won't throw a code on an lt1?

Or is the car just jealous I've been spending all my time the past week on her subie and it'll straighten itself out when I start on it in the next couple days lol?

ILuvPizzaTimes10 08-24-2010 10:18 PM

Iac motor died I'm guessing. Computer commands it closed on key. Then opens it on crank. 2 coils do this operation. I bet one has burnt. Or its just getting sticky. Take it off and clean it. Ohh and does your mph follwer work? That's wen you drive down the road and put the clutch in. It should keep a high idle until a complete stop.

My84Z 08-24-2010 10:18 PM

I'd guess vaccum maybe a rip or loose near the tb

bottledbird68 08-24-2010 10:30 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 27740)
Iac motor died I'm guessing. Computer commands it closed on key. Then opens it on crank. 2 coils do this operation. I bet one has burnt. Or its just getting sticky. Take it off and clean it. Ohh and does your mph follwer work? That's wen you drive down the road and put the clutch in. It should keep a high idle until a complete stop.

First time I noticed it was when it stalled going to pull into dunks. Stuffed the clutch at about 30 mph to slow down for the lot and it died.

It almost wants to idle but at just under 500 rpm. Doesn't last long lol. I was thinking vaccum but iac would make sense. Not many vaccum lines on this car.

Formula413 08-24-2010 11:27 PM

Yeah a vacuum leak would usually cause a high idle too. Sure sounds like the IAC, Camrys are notorious for that. Be careful if you clean it, I think I read that they are sensitive to harsh chemicals.

Batman 08-24-2010 11:33 PM

Fuck it, I'm going opti, it's ALWAYS the opti....

bottledbird68 08-24-2010 11:52 PM

Quote:

Originally Posted by Batman (Post 27762)
Fuck it, I'm going opti, it's ALWAYS the opti....

Tell me about it lol. It still throws both opti codes every cold start, done it as long as I've owned it, even with the msd opti. They go away as soon as it gets up to temp though so I gave up and stopped worrying about it.

ILuvPizzaTimes10 08-25-2010 12:24 AM

Low and high res pulse have come up on cold starts from a cam befofe. Not common but it happens. I say vacuum leak would cause high idle. Try it. Pull the brake booster hose off. Fucker will zing right up.

Batman 08-25-2010 12:28 AM

Lol, almost like you are adding unmetered air into the engine......

ILuvPizzaTimes10 08-25-2010 12:34 AM

Ahhhh yupppppp you so smaht

Formula413 08-25-2010 12:50 AM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 27772)
I say vacuum leak would cause high idle. Try it. Pull the brake booster hose off. Fucker will zing right up.

Funny thing is my car instantly dies if you pull that hose off. I did that when I seafoamed my car, I had to pinch it almost completely shut so the engine would still run.

ILuvPizzaTimes10 08-25-2010 12:53 AM

Did you pull it off after it was running?

bottledbird68 08-25-2010 01:17 AM

Ok, just took it for a quick ride again and it was fine lol.

So, I'm gonna go with pizza on this and guess that I have what's about to permanently bad iac ;)


On another note, more on this cam causing low and high res pulse signals? Car really is an absolute bitch until it warms up a little.

Formula413 08-25-2010 01:51 AM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 27783)
Did you pull it off after it was running?

I think I tried both, I know if I took it off with the engine running it died, but I think I tried starting it with the hose off too.

ILuvPizzaTimes10 08-25-2010 07:42 AM

Yeah alex it could go either way but if you pull it off then start it it will have a h igh idle and take longer to come down too

ILuvPizzaTimes10 08-25-2010 07:46 AM

And it seems more like tune then anything. Matt. What I would do is check iac counts and commanded idle. You would want to see 30-50 counts and you should idle at about 950 rpm. And your map should be around 45-55kpa. If any of the above are off too far in open loop it will run like a bag of ass.

KB93z28 03-15-2011 09:35 PM

Sounds like how my car runs sometimes, its hit or miss, some days it will run fine, other days it will idle real low, then die lol, or idle at about 2,000rpms, i replaced my IAC, no change.


All times are GMT. The time now is 10:24 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.