North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   LSX Powertrain (http://www.northeastf-bodyassn.com/forumdisplay.php?f=37)
-   -   Intake ideas? MAF Questions too. (again) (http://www.northeastf-bodyassn.com/showthread.php?t=2245)

Bayer-Z28 01-20-2011 11:51 PM

Intake ideas? MAF Questions too. (again)
 
It's down to the FAST and Vic Jr now.

Also, what MAF should I run? (Don) From a tuning stand point. I've heard you can go TOO big. If I'm running a 102 TB would a 100mm blade MAF be ok? I would think an 85mm MAF would be a restriction on a 102TB.

Anyway.. I was told a Vic Jr is wrong for my cam. Someone mentioned that it performs better with wide overlap cams. Mine only has 5* of overlap. Can I get a 95 or 92mm 120* elbow for the Vic Jr to clear the stock SS hood?

My84Z 01-21-2011 12:46 AM

Victor jr will make less down low but more up high where as the fast will make more mid but less peak and at top.

Batman 01-21-2011 01:40 AM

and stock cubes a Vic JR will kill you. Same with a FAST 102, there have been alot of complaints about them. I'd go with a Fast 92/92 and an 85MM Z06 MAF. But DEF I don't think you have anywhere near the cubes to pull off a Vic JR or a 102.

Slowhawk 01-21-2011 03:54 PM

I all comes down to the head and cam selection.No wide splits with victor junior intakes. LSA is best at 106-110.

Just did a 01 Z that made 445hp/400tq on my dyno with TFS 215 heads,230 cam,LS6 intake,ported TB,stock MAF, ARH headers and 12 bolt with 4.11 gears. Compare that to your #'s or even Batmans car on my dyno.( I think was 380hp or so).

941LE 01-21-2011 04:04 PM

393/366 were the dumbers Don. Gonna be seeing u when i get home

Batman 01-21-2011 07:58 PM

Quote:

Originally Posted by 941LE (Post 37086)
393/366 were the dumbers Don. Gonna be seeing u when i get home

Needs to be tuned too....

941LE 01-21-2011 08:00 PM

lol its what its for Nick

ILuvPizzaTimes10 01-21-2011 10:05 PM

Quote:

Originally Posted by Batman (Post 37099)
Needs to be tuned too....


needs more then tune.

Batman 01-21-2011 10:21 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 37108)
needs more then tune.

it NEEDS a tune to run correctly the way it is, after that it's up to him what to do with it. But at least it's running...:p

c4boom 01-22-2011 04:29 AM

mikes car runs we started it at the party :P

Formula413 01-22-2011 06:05 AM

Quote:

Originally Posted by c4boom (Post 37137)
mikes car runs we started it at the party :P

True fact, I was there :)

Bayer-Z28 01-22-2011 10:33 AM

Mine ran 403/38-something and needs a retune for sea level.

I've been wanting a retune, but I want to do the intake first. I'd like to see 440/390 out of this cam. It's a low end Tq cam, so I don't want anything that will kill the low end. It's got a 110* LSA, but only 5* of overlap.

I was just wondering about the MAF too because I was reading that you can go too big and that will throw the MAF off because it won't be getting a "bottle neck" (in a way) in order for it to get an accurate reading of what is really passing by its sensors. Too big is too slow, IIRC. I wonder if it'd be worth it to go SD tune.. I've asked around and the replies are mixed, but this isn't a DD car. It's just a street car.

I've been saying since day 1 that the 102 was too big for an LS1 and everyone was saying "Noez itss not!!! It's amazing!" but I never saw any numbers showing it was any better over a good 92 setup.

Bayer-Z28 01-22-2011 10:44 AM

And Don, if you find a FAST 92, could you PLEASE hold onto it for me!?!? For a decent price that is. Once tax season comes around I'll pick one up, IF I can find one that is. I found a damaged one on eBay last week, but I couldn't find the outer shell anywhere.

ILuvPizzaTimes10 01-22-2011 12:52 PM

why would sea level tune vs. 4000 feet tune make a difference on a MAF tuned car? maf should correct it self on a few street runs around here. and judging by your numbers your about right on for numbers based on the TSP bloated DynoJet numbers.

Fast sells the pieces to repair there intakes from individual runner to top and bottom "cases" if it was cheap enough id have bought it.

Bayer-Z28 01-23-2011 02:11 AM

^ I would have gotten that damaged FAST 92 if I could have found the shell easily enough.

If I could find all the pieces, I'd piece together an intake. :)

Batman 01-23-2011 11:48 AM

Wat Pizza is saying is FAST sells the shell pieces, you just have to call them

Bayer-Z28 01-23-2011 01:47 PM

I was wondering... I'll have to wait till I get my taxes done and give em a call. Doesn't make sense that they wouldn't sell the intakes anymore, but the pieces.

Bayer-Z28 01-24-2011 10:46 PM

85mm Delphi MAF on the way.. $75 shipped. :D

Found an ASP UDP with ARP Bolt AND both belts for $170 NIB.. But the fuker hasn't gotten back to me about it yet.

Bayer-Z28 02-07-2011 12:13 AM

Found flow #'s for the 92 and 102 non-ported. I've been looking for these for YEARS! 4" bore, but nearly same heads as mine. Worked over 243's. I'm running a .639" cam. I don't see the minimal gain being worth it for a 102 over a 92. Shown as head flow with the intake.

Would it still be ok to stick a 92mm TB on a 102 IM?

-=EDIT=-
On the contrary. Check out Mamo's post on here:
http://www.ls1tech.com/forums/genera...ween-fast.html

Quote:

Flowed our LS2, 243 CNC'd head on a 4.00" bore. Runner volume is ~225 cc and these are with 2.00" intake valves. These are going on a project here and since we have a few of the new 102's, I figured it was appropriate to update the flow numbers.

Fast 92 - Stock
.100 71.4
.200 144.7
.300 205.9
.400 235.7
.500 259.0
.550 270.8
.600 272.6
.650 276.2

Fast 102 - Stock
.100 74.4
.200 150.7
.300 211.9
.400 241.7
.500 265.6
.550 271.7
.600 274.0
.650 278.4

here is the link of the original post
http://forums.corvetteforum.com/c6-t...w-numbers.html

Slowhawk 02-07-2011 01:03 AM

Ok,so how does flow translate to hp/tq?

ILuvPizzaTimes10 02-07-2011 01:16 AM

stick a 3000 cfm intake on your car see if it really makes That much more power. flow numbers mean shit. i dunno why your researching this so much. the 102 is terrible from all the reviews ive seen on moderatly modded cars such as yours. like the PPI with FI or HUGE CUBES the extra CFM will be a waste if not completely rob your car of drive-ability and low end Anything. But it will make a few more peak MAYBE! i dunno man get what you can at a decent price. or what you can afford. my buddy installed a FAST 92 FAST TB and he gained ZERO miles an hour and ZERO ET over the LS6 he had. similar power levels to you. just food for thought.

Bayer-Z28 02-07-2011 01:48 AM

^ What heads was he running? What cam/lobes? Engine? All of this comes into play.
-And if flow numbers don't mean shit, then how do YOU buy a set of heads?? By looks?
-Like Mamo said, the head is what depicts what intake you should be running. And seeing as I was spec'd a set of AFR 205's, a good intake will be needed in the future.

I've always said that the 102 is too big, It's just that the deeper I look, the more conflicting evidence I find. I think a 92 and adding cats to my setup will help me keep my bottom end. I don't want to lose any because that's what this cam is for.

And I take flow #'s seriously. It's evidence that something is "different." I bought some cheap parts back then and didn't research them and I am royally kicking myself for it now. Hard to explain, but I DO research things to death before I buy them.

With these "quick" lobes (XE-R, IIRC) that I'm running, if the head can get to a higher flow earlier in the lift (Degrees of rotation = time also), the cam doesn't have to reach max lift (LOST time in rotation) in order to achieve a solid amount of airflow. = more cyl filling, more air earlier and quicker. The intake can obviously add a bit of a bottle neck to this. I don't want to say "restriction" because that's not the word. I also understand that if the runners are too big, it will lose port velocity. And yes, an engine can only injest soo much air.

I am looking to extract EVERYTHING this cam has to offer. I am damned to PROVE that it will perform AS GOOD if not BETTER than the other huge cams and that mine has much better driveability. I ran a 12.14 for my second time ever at the track, so this has something.

Yes, I'm stubborn. I'll get either the 92 or the 102. Not sure yet. I researched my cam for two years before I bought it and I'm only on about 6 months to a year researching the intake. It's fascinating to me. I want to know why it is as good as it is.(or is not) I started looking into things and as soon as I opened a can of worms, I just kept wanting to know more. This is a hobby of mine, I guess. Research.

Slowhawk 02-07-2011 03:03 AM

Cam is the cheapest.

I like Mamo but don't listen to him much anymore. Never seen one of his custom Mamo H/C setups make more then 430rwhp even though it is a 460-470rwhp package.

XER Cams are just valvetrain killers. Stopped ussing them years ago,much better cams out there now.

Batman 02-07-2011 03:43 AM

I was gonna say, if you can't use that much air it is useless to you. A 346 is never gonna push that kind of volume. I mean realistically cam only an LS6 intake is probably one of your best options

Batman 02-07-2011 03:47 AM

Quote:

Originally Posted by Bayer-Z28 (Post 38289)
^ What heads was he running? What cam/lobes? Engine? All of this comes into play.
-And if flow numbers don't mean shit, then how do YOU buy a set of heads?? By looks?
-Like Mamo said, the head is what depicts what intake you should be running. And seeing as I was spec'd a set of AFR 205's, a good intake will be needed in the future.

I've always said that the 102 is too big, It's just that the deeper I look, the more conflicting evidence I find. I think a 92 and adding cats to my setup will help me keep my bottom end. I don't want to lose any because that's what this cam is for.

And I take flow #'s seriously. It's evidence that something is "different." I bought some cheap parts back then and didn't research them and I am royally kicking myself for it now. Hard to explain, but I DO research things to death before I buy them.

With these "quick" lobes (XE-R, IIRC) that I'm running, if the head can get to a higher flow earlier in the lift (Degrees of rotation = time also), the cam doesn't have to reach max lift (LOST time in rotation) in order to achieve a solid amount of airflow. = more cyl filling, more air earlier and quicker. The intake can obviously add a bit of a bottle neck to this. I don't want to say "restriction" because that's not the word. I also understand that if the runners are too big, it will lose port velocity. And yes, an engine can only injest soo much air. FOr the cam you have you will never make the HP numbers of bigger cams, it is not a possibility. But staright HP numbers are about as worthless as CFM numbers. Build the car to run the way you like it and forget about the numbers. Talk to Pros like Don to help you get the exact set-up you are looking for and don't be blinded by numbers that in the scheme of things don't determine how a car runs

I am looking to extract EVERYTHING this cam has to offer. I am damned to PROVE that it will perform AS GOOD if not BETTER than the other huge cams and that mine has much better driveability. I ran a 12.14 for my second time ever at the track, so this has something.

Yes, I'm stubborn. I'll get either the 92 or the 102. Not sure yet. I researched my cam for two years before I bought it and I'm only on about 6 months to a year researching the intake. It's fascinating to me. I want to know why it is as good as it is.(or is not) I started looking into things and as soon as I opened a can of worms, I just kept wanting to know more. This is a hobby of mine, I guess. Research.

Flow numbers are only part of the story, Knowing how much CFM your engine can actually push and matching the heads to the cam, intake, fuel etc. You can bolt a set of 300+CFM heads to your 346 and if you can only push 215CFM then you are wasting your time and most likely causing the engine to run poorly. Also where are these huge CFM numbers? if it is over .600" lift you probably aren't going to like what you get. You need to find the correct CFM for your set-up and your best bet with that is to talk to someone like Don or buy a complete package. You also need to consider combustion chamber size, shape, etc. Buying heads just by CFM doesn't make much sense.

Bayer-Z28 02-07-2011 01:58 PM

^ I have found that the TFS heads flow more at the mid lift numbers. The exhaust flow is up there also compared to the AFR heads. Mid and low lift #'s are where the money is. Such as a set of stock heads that flow maybe 160 cfm at .300" and top out at .600" at 220cfm. If you can get that head to flow more, sooner, you won't have to run a HUGE lift cam. My .640" cam was a bit much for me, but I had to compromise on something. I wanted under 230 duration and around .600", but the reviews on this cam were pretty good. .600" lift, initially, scared me off, then I warmed up to the idea. The MS cams never caught my eye. But the Torquer V2 and 3 were an option when I was buying mine.

And from what I've read, these heads will always outflow the plastic intakes.

I was wanting a set of the TFS heads for a while and asked what heads were recommended and they actually spec'd me a set of AFR 205's. I'll do those eventually and save the TFS idea for an L92/LS3/LS9 clone idea I've been tossing around. And the guy who spec'd my cam has had a setup push 550rw with NA h/c. -Not with my cam, but still. I have an idea how to extract what I'm looking for.

84ta406 02-07-2011 07:55 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 38285)
stick a 3000 cfm intake on your car see if it really makes That much more power. flow numbers mean shit. i dunno why your researching this so much. thought.

Agreed flow #'s do mean shit, Anyone can port a intake or head to push out CFM, now to retain velocity is a different ball game. If theres too much volume the air speed slows down. Buy me a Super Victor and watch my car fall on its face.

Quote:

Originally Posted by Bayer-Z28 (Post 38289)
^ What heads was he running? What cam/lobes? Engine? All of this comes into play.
-And if flow numbers don't mean shit, then how do YOU buy a set of heads?? By looks?

Like Nick said, flow #'s are only part of it. Whats the use of so much flow if the heads cant handle it? Now you turned your intake into a bottle neck.

I look at heads based off chamber design, intake/exhaust port sizes, Min/Max CSA, etc. Theres a lot more to it IMO. You also have to look into how big the motor is, compression, cam profile and crap. Some heads and intakes work better with different cams.

Batman 02-07-2011 10:03 PM

IMO TFS > AFR for a street/strip application. The AFR's make more peak but the TFS's seem to carry a wider, broader power badn

ILuvPizzaTimes10 02-08-2011 12:00 AM

ive seen more cars make power with AFR then TFS lately. the fast as cast is a joke and id take AFR over an out of the box TFS head.

Bayer-Z28 02-08-2011 12:02 AM

^ I've ALWAYS wanted the TFS heads just because of the mid-lift numbers. They don't need a HUGE cam for them to flow crazy. I've always had my eye on the Torquer V2 or 3. I like those cams and the sound, but TSP seems to only be into higher RPM power and TR seems to do their research in power under the curve.

I think the 215's would still work, but the 205's may have a better velocity. And I'm looking into clarification on "these heads will always outflow the plastic intake" claims. A 102 unported may just be a match. Ported it flows over 280cfm at around .500". My heads peak out at around .280".

And from what I've gathered, the 102 design isn't an increased overall intake VOLUME, it's just a better runner design. And the gurus are saying that the throat has little effect on this, actually. Claims are that they almost needed a radius on the TB during testing of the 92 and the 102 did not need one. The air was slightly obstructed entering the 92mm TB right at the edges of the TB, while on the 102 it was not. Now, I'm wondering if that is from a decrease in air speed entering the TB. Same volume with a larger "hole" would mean slower.... Right? 0_o


And I've got LSK lobes on my cam. Asked the guy who designed it. I can't find my cam card.. :-\

Batman 02-08-2011 01:12 AM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 38333)
ive seen more cars make power with AFR then TFS lately. the fast as cast is a joke and id take AFR over an out of the box TFS head.

Agreed, but TFS kills them in the low and mid range which would be preferable for a car mostly driven on the street, IMO anyway. Once again you throw peak dyno numbers in the garbage with the other numbers, in the scheme of thing they only tell you part of the story. I don't care if the car makes 50 more HP at peak RPM if the "lesser" heads make more power across 80% of the RPM range then the only place you are really gonna see an advantage with the higher HP number is on the racetrack, and chances are it will be a negligible difference. I will take bigger low/mid range numbers over peak HP any day of the week in any application except a pure track car

Bayer-Z28 02-08-2011 01:20 AM

^ This is why I research stuff.. :D Peak numbers don't mean as much to me. I look at lot at the mid-lift and middle of the powerband numbers. My buddy has an MS4 with PRC heads and he swears by it, but I pulled on him even though he made more power than I did. I've driven it and I don't care for it as a street cam. I've noticed that TR seems to pay more attention to all around performance and TSP seems to be just peak power. I figured that out a couple years ago.

The TFS also runs a lower valve angle which can also help run a different range of cams due to a slightly less risk of PTV clearance.

Slowhawk 02-08-2011 01:31 AM

I won't buy AFR heads anymore. Build quality sucks. We mostly prefer to use TEA/TFS heads. They always outperform AFR,ported TSP heads ect.

84ta406 02-08-2011 07:05 AM

Quote:

Originally Posted by Batman (Post 38336)
Agreed, but TFS kills them in the low and mid range which would be preferable for a car mostly driven on the street, IMO anyway. Once again you throw peak dyno numbers in the garbage with the other numbers, in the scheme of thing they only tell you part of the story. I don't care if the car makes 50 more HP at peak RPM if the "lesser" heads make more power across 80% of the RPM range then the only place you are really gonna see an advantage with the higher HP number is on the racetrack, and chances are it will be a negligible difference. I will take bigger low/mid range numbers over peak HP any day of the week in any application except a pure track car

Greater AVG. power > Peak power with a lower average IMO as well. I dont know all this LSx crap but I will say if you go to the track, you wont see many AFR headed cars. Brodix FTW! lol

Bayer-Z28 02-09-2011 12:32 AM

I'm torn.

I've seen all the data and I'm just still worried about losing low end on the 102. I've got the money to buy it now. Just last minute jitters, I guess.

Batman 02-09-2011 02:17 AM

I think the 92 or 90 would be a better fit for you if you can get your hands on one.

Formula413 02-09-2011 02:36 AM

Between the bad things I've heard about the 102 and just the fact that it's huge and your motor is stock cubes and not too radical a cam it doesn't seem like a good fit to me. Have you heard good things about it in your research?

Batman 02-09-2011 02:41 AM

I would almost go LS6 or an LS2 intake over a 102.

Bayer-Z28 02-09-2011 03:14 AM

^ The LS6 outperforms the LS2. LS2 is a turd compared to the 6 and 3. The TB size doesn't make the intake and has little to do with it. I've learned a LOT this week.. :)
As I see it, the 102 is almost an ITB intake wrapped in polymer/plastic.


Check it.. This settles it.

Quote:

Originally Posted by Tony Mamo @ AFR (Post 14476527)
OK...this thread is pretty funny talking about nothing....LOL

Guys...

When we are discussing fuel injected applications.....the size of the plenum and the opening or the TB (size) will have zero effect on "low end" power.

This is old school thinking stemming from the very real and often practiced applications where too large a carb might have been bolted on a particular engine combination.

The problem stemming from the fact the large carb slowed the airspeed down enough in the venturi's of the main body to negatively effect the carb atomization and therefore hurt power, torque, fuel economy, and responsiveness until enough RPM was generated to allow the carb to become more effective again (guys older than 45 will be nodding their heads up and down right now while reading this!).

We aren't atomizing fuel here folks....thats handled by the injectors and the real meat and potatoes of manifold design (runner length, shape, and taper) hasn't changed much from the 90, 92 or 102.....its very similar but the 102 does have a superior shaped runner (although the length is very similar), is slightly taller, and ultimately flows more, especially when properly ported.

Yes....a FAST 102 can flow more than a 280 CFM head but thats always the case with a really good intake....ideally you want ALOT of headroom when selecting a manifold so when you bolt it in front of your heads it flows more net to the cylinder with the ultimate situation to not hurt the port any more than placing a radius plate in front of it. Thats pure theory unless we are discussing extremely optimized straight shot tunnel ram style manifolds.

I can port a Gen I single plane intake and make it flow 400 CFM.....when you place it in front of a 300 CFM intake port that port still loses 20 CFM which is very good all thing considered. Take the same intake unported by me that still flows way more out of the box than the 300 CFM intake port in question (say the intake flows 360 CFM out of the box) and now you may only see 265 CFM when placed in front of the head because it hurt the net flow more.

INTERNET MYTH #1 .....My 102 Fast is too big for my 346

Wrong....its a better designed intake thats going to allow more air to pass thru the intake ports and be mixed with more precisely atomized fuel from your injectors.

INTERNET MYTH #2....Its already big....you dont need to port it (or it might hurt the bottom end).

Also wrong....at least when ported properly. Once again it simply makes a good piece even better but I would be the first to admit that on a marginal set of head the gains from the work would be less as well. The better the heads, the more aggressive the RPM, displacement, etc. the more that ported 102 is going to pay you in spades.

The larger the restriction the intake manifold becomes....the better your results will be when you swap to the better intake.

If your still questioning anything lets get it handled now and please refer other people back to the answers when we see the same questions and bad information in other threads....I wish I had a nickel for the guys convinced their inaccurate theories are accurate....LOL

The ONLY potential negative to the 102 design...well besides the cost of admission with the rails etc.....is the TB (airblade) is so large it can create drivability challanges with the tune but its a much easier deal on a cable operated 102 with an IAC motor. ALso, it tends to be extremely responsive which I personally like, however some have complained its too responsive (on/off) and they have to get used to driving it. No big deal in my book....

Hope this helps!

-Tony


ILuvPizzaTimes10 02-09-2011 03:44 AM

i dont agree with that completely. larger intake runners on an engine say at at low rpm and low vacuum. the air can stall in the ports. too big a plenum on a small displacement engine spinning at low rpm/high load will stall air inside the plenum. i mean believe what you wwant. real world is real world not some engine dyno/chassis dyno and the car made 40 more rwhp but ran 3 tenths slower...... i mean get it if you wish. if you choose to believe a guy who ultimatly is a sales man for FAST. of course he's going to tell you its great. and you wont lose anything. there are back to back tests on this i believe hot rod did it and the 102 lost everywere but peak over the 92/92 setup SAME 92mm tb. if i read it right.


All times are GMT. The time now is 10:18 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.