North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Fourth Generation (http://www.northeastf-bodyassn.com/forumdisplay.php?f=16)
-   -   started my cam/intake swap last night! (http://www.northeastf-bodyassn.com/showthread.php?t=2675)

danZ28 04-17-2011 05:20 PM

started my cam/intake swap last night!
 
It's my first time doing a cam/intake swap. I'm also doing the new style ls6 PCV conversion. Just finished stripping the heads down and I'm taking a lunch break so I figured I would make a post.

List of parts included..

custom Patrick G spec'd EPS cam
PAC 1518 springs
Trickflow 7.425 pushrods
LS6 oil pump, LS2 timing chain
LS6 intake
New style LS6 valley cover & coolant tube
Port&Polished stock throttle body
Bosh 30lb/hr @ 43.5 psi injectors
Powerbond UD Pulley & belts
ARP crank bolt & cam bolts
Lots of new gaskets and seals.

Dreading removing/installing the crank pulley, hopefully I won't have problems with it.

OH and I did NOT break the oil pressure sender! haha I am proud of myself

I sent the computer out UPS last night to get it tuned. Hopefully I can drive the car afterwards out to Bridgewater and meet Don :)

black heartbeat 04-17-2011 06:33 PM

sounds awesome man get some pics up on the progress!

SLP IROC-Z 04-17-2011 06:43 PM

is this thing gonna go vroom vroom or what

smokinss 04-18-2011 12:15 AM

Sounds good man. The crank bolt shouldnt be too bad as long as you have a big enough compressor and strong enough gun. If not then good luck.

danZ28 04-18-2011 12:33 AM

I didn't really have that much problem with the crank bolt, and the balancer came off fairly easy once I got the right 3 jaw puller. 1/2 breaker bar with a 24mm impact socket, then a 4 ft piece of rigid pipe on it... started pushing from the drivers side and got around and started pulling down on it. Seemed like the bar just about bent around to the passenger side before the bolt broke free.

Right now I'm having a hard time getting the passenger side dowel rod in to hold the lifters out of the way. Driver's side slid in easy. Guess I'll just have to play with it some more.

I'll post some pics later when I'm done for the night!

Batman 04-18-2011 01:02 AM

Make sure you do not re-use the old bolt for the pulley, good time to switch to a re-useable ARP bolt

danZ28 04-18-2011 01:34 AM

Quote:

Originally Posted by Batman (Post 44395)
Make sure you do not re-use the old bolt for the pulley, good time to switch to a re-useable ARP bolt

Yup. One came with my pulley when I ordered it from Scoggin-dickey

Decided to call it a night after I got the pass-side dowel in. the 5/16" rod would not fit, so I decided to use some 1/4" brake line I had instead. Worked out nicely.

Cam comes out tomorrow after work.

http://img219.imageshack.us/img219/3236/dscn0096q.jpg

http://img508.imageshack.us/img508/6754/dscn0098c.jpg

http://img26.imageshack.us/img26/4945/dscn0099r.jpg

Very happy with the rattle can paint job on the intake. My buddy though it was brand new when he saw it today.
Doing pretty good for my first swap I think. Haven't broken anything yet (that I know of :D)

Batman 04-18-2011 02:02 AM

What, no faith in the lifter retainers?

danZ28 04-18-2011 02:11 AM

haha. I like to be safer than sorry most of the time. Dropping the oil pan and fishing for a lifter would be another whole project in itself :sFun_explosive:

Batman 04-18-2011 12:08 PM

if you are lucky enough that it makes the oil pan, I don't think it is clearing the crank,rods, and then there is also the windage tray in the way

ls6monte 04-18-2011 04:28 PM

Quote:

Originally Posted by Batman (Post 44395)
Make sure you do not re-use the old bolt for the pulley, good time to switch to a re-useable ARP bolt

Tell that to Don! lol


Looks good!

DemonWithin99 04-18-2011 05:32 PM

looks good, should have towed it to don for a real tune... ::tuner plug::

danZ28 04-18-2011 11:19 PM

Quote:

Originally Posted by DemonWithin99 (Post 44442)
looks good, should have towed it to don for a real tune... ::tuner plug::

I know. I wish I could have, but my little 4 banger daily driver ranger does not have the balls to tow the car. Hopefully the mail tune isn't too bad for the time being

Slowhawk 04-19-2011 12:20 AM

Alot of my customers get a mail tune to get to me. That cost goes towards there full tune bill.(if done at a reasonable timeline).

I hate mailorder tunes and won't send permanent ones.About 90% of the one's I see are dangerous and just hope the KR sensors work to save the motor.

danZ28 04-19-2011 12:46 AM

Quote:

Originally Posted by Slowhawk (Post 44464)
Alot of my customers get a mail tune to get to me. That cost goes towards there full tune bill.(if done at a reasonable timeline).

I hate mailorder tunes and won't send permanent ones.About 90% of the one's I see are dangerous and just hope the KR sensors work to save the motor.

I really wish I knew that last week when I sent my computer out. Damnit :(

Well, I got the new cam in today and the oil pump off. Lined up the crank and timing gear dots. A guy down the street from me who has done a lot of LS1 motor work said he'll check them for me before I put everything back together. Hopefully he's free tomorrow.

ILuvPizzaTimes10 04-19-2011 01:47 PM

check them? go dot dot. spin the motor 4 complete Crank revolutions and make sure they line back up. if your worried. Done

and id be willing to bet the ecu just got there and they havent gotten to it yet call em up and say DON TOUCH IT! and just pay the return shipping. then have a friend or use your AAA to get the car to bridegwater.

danZ28 04-19-2011 08:37 PM

#1 cylinder has to be at TDC when the dots are lined up, correct?

ILuvPizzaTimes10 04-20-2011 01:33 AM

si senior

smokinss 04-20-2011 12:02 PM

Looking good. You could of done the pen magnet method like I did to hold up the lifters. I got 16 retractable pen magnets and just slid them down the pushrod holes to hold up the lifters.

Formula413 04-20-2011 06:53 PM

Nice work, should be a solid setup when it's done and tuned. I'd like to see it when it's out and about, let me know if you want to meet up sometime. I'm down in Chicopee but my Formula is in Northampton.

danZ28 04-21-2011 02:14 AM

Quote:

Originally Posted by Formula413 (Post 44566)
Nice work, should be a solid setup when it's done and tuned. I'd like to see it when it's out and about, let me know if you want to meet up sometime. I'm down in Chicopee but my Formula is in Northampton.

Right on man. I'll let ya know when it's drivable. Hopefully going to have it all back together by the end of this long weekend coming up.

danZ28 04-26-2011 02:25 AM

It runs!!

ILuvPizzaTimes10 04-26-2011 02:26 AM

BUT DOES IT RUN GOOD?!?!?!


All times are GMT. The time now is 03:15 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.