North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Lounge (http://www.northeastf-bodyassn.com/forumdisplay.php?f=2)
-   -   Cam degree wheels (http://www.northeastf-bodyassn.com/showthread.php?t=3968)

Motaboata 04-02-2012 10:22 PM

Cam degree wheels
 
I was wondering if anyone has a cam degree wheel and setup to properly degree the cam in place. I am willing to give some money for a rental! let me know

thanks

josh
774 210 2657

BigMac76 04-02-2012 10:29 PM

Would love to man, but a buddy of mine in Fall River has it right now dialing in his vette. I will give him a call and see if he's done with it or what. Only cost me $20 from summit. Not sure if Autozone would have one of these as a "loaner" tool or not.

KLAB 04-02-2012 11:15 PM

whats with engine builders with no tools these days...

Motaboata 04-02-2012 11:26 PM

im not an engine builder, 1st time doing it tryna save a few bucks

My84Z 04-02-2012 11:29 PM

Why do you want to degree it? With your application especially leaving it n/a at the moment and possible spray later?

KLAB 04-02-2012 11:34 PM

well i mean if you plan on building motors again it would be nice to have one but i see your point in interest in savings

Motaboata 04-02-2012 11:39 PM

@ John, I wanted to make sure everything is right and dead on. I was told i could just line up the markings etc... Just tryna be over cautious and yes a lil spray in the distant future

My84Z 04-02-2012 11:50 PM

Just line the dots up perfectly :)

Motaboata 04-02-2012 11:56 PM

Quote:

Originally Posted by My84Z (Post 65613)
Just line the dots up perfectly :)

thanx dad

My84Z 04-02-2012 11:58 PM

Hahahhaa yes son

ILuvPizzaTimes10 04-03-2012 12:30 AM

what are you running for a cam. what piston have you checked PTV before bothering degreeing it. if it was a CLOSE tolerance setup i would say its a must. but other wise dot to dot. especially if your using stock gears and a C6R chain?

BigMac76 04-03-2012 11:06 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 65624)
what are you running for a cam. what piston have you checked PTV before bothering degreeing it. if it was a CLOSE tolerance setup i would say its a must. but other wise dot to dot. especially if your using stock gears and a C6R chain?

Agreed, line em up at 6 and 12 and you should be fine. Unless there is something specific you're shooting for...btw my friend hasn't even started putting his cam in yet, but "promises" he should be done with it by this weekend. In other words, I'll probably see it 6 months after you've installed it lol

Motaboata 04-03-2012 11:18 PM

My project got put on hold till end of April. Army called today leave for school thursday

84ta406 04-03-2012 11:58 PM

I always degree in my cams, I like knowing its EXACTLY where its supposed to be. When you get back Josh, you can use mine.

ILuvPizzaTimes10 04-04-2012 11:59 PM

lets say its 3 degrees off. knowing that without an adjustable timing set its not changable? so unless its over a tooth off(~6-12 degrees) no harm can be caused by it. i dunno that my take. if it was a 1200 horse/7K+ rpm monster then do it. i could be wrong.

Formula413 04-05-2012 01:06 AM

I was going to ask what you would do unless it was off by a whole tooth.

ILuvPizzaTimes10 04-05-2012 01:47 AM

if the cam is FAR off the spec. it was ether ground incorrectly or the timing set is wrong. thats REALLY what your checking wen you degree a cam. just confirming the cam card. and 98% of the time they are right. and like i sed only if its a TIGHT motor. like PTV is speced under .100 then you check it.

84ta406 04-06-2012 01:37 PM

I always use adjustable sets. I do it for piece of mind, that and because some cams I do are supposed to be installed other than "straight up"


All times are GMT. The time now is 05:07 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.