North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Pictures/Videos (http://www.northeastf-bodyassn.com/forumdisplay.php?f=12)
-   -   car is going back to Stock lol (http://www.northeastf-bodyassn.com/showthread.php?t=4852)

camarokid91 04-01-2013 02:09 PM

car is going back to Stock lol
 
This may sound ridiculous especially on this forum when everyone is trying to make their cars go fast in a straight line which has never been the case for me. I will be taking my 433 Hp motor out to replace it will a stock LS1. Started the process this weekend but ran out of day light.

https://lh4.googleusercontent.com/-9...330_184644.jpg

Here is a photo from the last time I did this.

https://lh4.googleusercontent.com/-U...-08-28_200.jpg

smokinss 04-01-2013 03:55 PM

Cool. But a couple questions. Why? And why not go out the top? You selling the Camaro?

camarokid91 04-01-2013 09:28 PM

It's starting to look that way. Also with the scca Esp is the class where camaro's are highly competitive. Which requires a stock motor, so I will be racing in esp or getting a Z06.

My84Z 04-01-2013 10:07 PM

Looks like parts for sale lol

camarokid91 04-01-2013 10:29 PM

Quote:

Originally Posted by My84Z (Post 79032)
Looks like parts for sale lol

Probably going to keep the built motor and stroke it.

KLAB 04-03-2013 02:05 AM

and put it innnnnnnn ????

MY CLEAN LT1 SHELL

camarokid91 04-03-2013 06:28 PM

Quote:

Originally Posted by KLAB (Post 79094)
and put it innnnnnnn ????

MY CLEAN LT1 SHELL

Rx7 FC or FD someday is what I hope to do.

camarokid91 04-08-2013 12:58 PM

Update:

https://lh3.googleusercontent.com/-u...406_120536.jpg

https://lh6.googleusercontent.com/-Q...406_121241.jpg

https://lh4.googleusercontent.com/-A...406_124915.jpg

https://lh4.googleusercontent.com/-5...407_165729.jpg

https://lh6.googleusercontent.com/-q...407_165726.jpg

LSX-Nation 04-08-2013 11:11 PM

Nice!

KLAB 04-09-2013 01:15 AM

oooo stranos? you gonna sell em?

ILuvPizzaTimes10 04-09-2013 02:49 AM

good idea and probably the only real use for a strut bar!!! haha Looking good. had to use a hoist for one of my engine pulls. lifts just make you lazy right?!?!?!

camarokid91 04-09-2013 01:25 PM

Quote:

oooo stranos? you gonna sell em?
With the car if I sell it. IMO the stranos where best mod I did to the car. I don't feel like wrenching for a bit after I get the motor back in. I feel like I always have this car apart.


Quote:

Originally Posted by ILuvPizzaTimes10 (Post 79247)
good idea and probably the only real use for a strut bar!!! haha Looking good. had to use a hoist for one of my engine pulls. lifts just make you lazy right?!?!?!

Yeah it makes rolling it around cake. The A arms stay ridged instead of falling all over the place. Lifts are great I would love to get/use one but I'm 24 I think be ok as long as there's beer around while I'm working on the car.


The motor should be going back in this weekend and then its time to get it re-tuned and beat the car up some more Autocrossing.

KLAB 04-10-2013 06:28 PM

I would like to get stranos

camarokid91 04-16-2013 02:21 PM

My car runs lol

ILuvPizzaTimes10 04-17-2013 02:58 AM

pics or it didnt happen!!!!!

camarokid91 04-30-2013 06:55 PM

I hate cars continued.................

http://i.imgur.com/9SU7KiPl.jpg

ILuvPizzaTimes10 05-01-2013 02:40 AM

k&n filter makes a nice bench!!!! Why is it apart again??

camarokid91 05-01-2013 01:30 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 79874)
k&n filter makes a nice bench!!!! Why is it apart again??

Motor I put in has a bad lifter and is ticking. I'm hoping replacing all the lifters and rods will sort this out.

smokinss 05-01-2013 03:19 PM

Been there before. Actually might be doing that to mine too.

Slowhawk 05-01-2013 05:49 PM

Make sure you find something bad before throwing parts at it.

ILuvPizzaTimes10 05-01-2013 05:51 PM

what cam are you using? base circle? heads cut? stock push rods/longer? alot of things make a "bad" lifter noise that have nothing to do with lifters.

camarokid91 05-01-2013 08:42 PM

Quote:

Originally Posted by Slowhawk (Post 79892)
Make sure you find something bad before throwing parts at it.

So I have a full set to replace the currents from my co workers recent cam swap. I'm basically just supplying gaskets and my time to do this. Don the noise actually completely stopped (weird) when I got home from picking the car up, then I let it idle for 30 minutes and it started again. I'am 90% on the lifter being the issue, the rods are all fine.

camarokid91 05-01-2013 09:12 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 79893)
what cam are you using? base circle? heads cut? stock push rods/longer? alot of things make a "bad" lifter noise that have nothing to do with lifters.

This is on a 100% stock unopened ls1. Heres the noise.


My84Z 05-01-2013 09:37 PM

Did u change the oil? Most likely it could be a lifter but simple things first

ILuvPizzaTimes10 05-02-2013 12:33 AM

and what was the hot idle oil pressure?

camarokid91 05-02-2013 02:32 AM

Pressure is all normal 45 at hot idle 60 under load. Car has new oil in it and seafoam.

Slowhawk 05-02-2013 10:06 PM

Probably a bad lifter then. Was knocking pretty good here but if the noise went away I would guess lifter.

camarokid91 05-06-2013 11:29 PM

Car no longer ticks. Thank God. It was a weak lifter.

ILuvPizzaTimes10 05-06-2013 11:38 PM

Nice!!!!! Sucks yah had to rip the heads off!! Stupid LS1!!!

smokinss 05-07-2013 01:20 AM

Good deal. Just got mine torn down. Heads will be off tomorrow

camarokid91 05-07-2013 01:11 PM

Quote:

Originally Posted by smokinss (Post 80044)
Good deal. Just got mine torn down. Heads will be off tomorrow

It not that bad as long as you take your time. Just make sure you get a pipe for leverage.

smokinss 05-07-2013 02:54 PM

Oh trust me I know. This isnt the first time I have had the top end apart. I have had the motor in and out of the car 2 times since last year. I had to replace the oil pump last month and now this. Plus I had to do lifters/cam in my wifes Z28.

camarokid91 05-07-2013 03:20 PM

Quote:

Originally Posted by smokinss (Post 80063)
Oh trust me I know. This isnt the first time I have had the top end apart. I have had the motor in and out of the car 2 times since last year. I had to replace the oil pump last month and now this. Plus I had to do lifters/cam in my wifes Z28.

lol you sound like me. 2 years 2 motor swaps, 2 top end rebuilds.

BryanH 05-07-2013 07:41 PM

Wow... this has been something I've thought about from time to time too. But I will keep what I have.

camarokid91 05-08-2013 12:33 AM

Quick update:
Motor is in and back together makes no noises
Installed my turn one PS
Installed global west upper A arms

https://lh5.googleusercontent.com/-j...255B1%255D.jpg

https://lh3.googleusercontent.com/-H...534%5B1%5D.jpg

https://lh3.googleusercontent.com/-F...255B1%255D.jpg

https://lh4.googleusercontent.com/-u...255B1%255D.jpg

ILuvPizzaTimes10 05-08-2013 02:40 AM

Nice!!!!! how is the pump? dead quite???? he sed he will still do the LT1 pumps but if it needs hard parts it can be repaired as you cant get any that are any good(china)

camarokid91 05-08-2013 02:57 AM

The pump is great its slightly harder to get the wheel to full lock but I like it.

ILuvPizzaTimes10 05-08-2013 06:01 PM

isnt that the point? or do these things understeer? i do quarter mile and fuck off on off ramps haha.

camarokid91 05-09-2013 01:03 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 80133)
isnt that the point? or do these things understeer? i do quarter mile and fuck off on off ramps haha.

Well I believe the theory behind these specific pumps are they assist the driver less in order to reduce temps inside the pump and make your lines smooth (less steering input). I do not understand what you mean by understeer? Are you referring to the car pushing the front tires into a corner? If so this would have to do with your suspension setup and is irrelevant to the power steering pump.


All times are GMT. The time now is 09:44 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.