Am I being paranoid? Lifter noise? (video)
Ok so all of you know the issues that I have had over the past several months. Now that the car is running again. I am not sure if I am being paranoid about engine noises or if the car is making a lifter tick. I already tried tighning down the header bolts. I pulled the valve cover and checked pushrods, rockers, and checked to see if a lifter was collapsed by pushing down on the pushrod to see if the lifters moved. Everything seems ok. When my wifes car had a bad lifter the noise got worse over a small period of time (2 or 3 days) and starting making a chirping type noise. The noise hasnt got worse, so I would think thats a good thing. This is more of a ticking but it seems more than the usual ls1 sewing machine noise. Here is a video and its coming from the driver side. I will try to take a better video if need be.
http://i56.photobucket.com/albums/g1...ps6599aef1.jpg |
mine sounds like that to. its quiet when its cold but has the sewing machine sound at full temp. annoys the shit out of me.
|
It's the springs or lifter preload.
|
So do I need new springs? How would I check or change lifter pre-load? Pushrod length not right?
|
Just a little update. I haven't really driven the car lately and decided to take it for a drive. Noise is still there. Just out of paranoia I drained some oil and checked the plug for metal. All seems good. Like Don said could it be the valve springs being worn? My first motor didn't seem to make this noise. I am using the same length push rods. 7.4 valve springs are patriot dual golds.
|
have heard them that noisy after the heads have been cut. were the heads cut if so how much? may need a push rod length checker to narrow it down. pull a valve cover and a rocker or 2. make sure the contact patch is in the center of the valve tip. if need be use some marking compound to verify.
|
Heads haven't been cut to my knowledge. Checked the pattern and all seems good
|
if the rockers are contacting in the center of the stem and you didnt change anything like the cam. it might be spring. and honestly unless its getting worse or you have some nasty low rpm(<5000) valve float. i wouldnt be worried.
|
Yeah that what my plan was. If it doesn't get worse than oh well.
|
called my buddy today. He has a push rod checker. Said he might stop by Sunday to help me check.
|
Cam does not affect swipe pattern.
|
Good to know. Ran it pretty good today. Took it to 6800 a few times. Noise hasn't gotten worse. Thinking it could be springs.
|
Quote:
|
Quote:
|
true didnt think of that aspect of it.
|
Thanks. Didn't really think a untouched ls1 could have a big differences in tolerance. Still waiting on my friend to come by with his pushrod checker.
|
I don't even own a pushrod checker. LOL
There are other ways. |
Quote:
|
count the turns after zero lash/preload on the lifter.
|
For my own sanity I ordered a set of ls7 lifters/ls1 trays from Scoggin Dickey. Heads will be off tomorrow. They are running a deal. 139.00 for the lifters/trays and the 8mm tray bolts. Also picked up some new mls head gaskets. If it still has the noise then so be it.
|
Got it torn down. Not sure if this would make the noise but it can't be good. Both lifters in cylinder 7 were like this.
http://i56.photobucket.com/albums/g1...ps8aa1b5e0.jpg |
I wonder if that's from when you had the oil pump prob.
|
take a good look inside the plastic trays. same grooving? the lifters might have been slightly rotating in the bore. check the roller trunion at the bottom for cupping(best way i can describe it)/uneven wear if any. will usually mean the cam has wear as well.
|
Lifter rollers look good. Found one with very minimal wear. Cam lobes look good from what I see. Spoke withDon about it already
|
Got the car buttoned up today. Sound seems to be gone. Haven't driven it yet. Just has the regular sewing machine noise
|
Nice!!!!! Congrats! what an up hill battle????
|
Tell me about it. But some of its my fault. Should of put new lifters oil pump when it was put together the first time. Just didn't have the funds and the guy didn't want the motor hanging around waiting for parts.
|
Let this be the end of your ls troubles! Lol
|
Id like for someone to take a wack at what my pushrod length should be.
Stock block, no decking LS6 cam Stock heads cut .025 Ls7 lifters GM mls stock gasket any takers? |
Quote:
|
Its about .060 Don. 1.5 turns to 22ft-lbs from zero lash. Looked up a article and guy figured .040 per full turn from zero lash. This is a estimate though. Picking up a pushrod checker this weekend
|
1.5 turns is over .080 if i remember right. 1.5 turns is pretty tight.
and Joe can i take a crack at it??????? |
sure
|
Here is the article I read
FWIW, EVERY cam install I have done using the LS7 lifter with a cam with greater than .600" lift (read smaller base circle) AND stock heads w/GM MLS gaskets has taken 7.425" pushrods for ~.050"-.060" preload. We measure lifter preload on each and every cam install we do. I have never had a lifter failure nor do we end up with the dreaded "sewing machine" noise. Its very simple, If you change ANY of the following: valve sizes, valve job, head milling, thinner/thicker head gaskets, decked block, cam with an altered base circle, etc... YOU MUST CHECK FOR PROPER PUSHROD LENGTH. I have helped countless numbers of individuals with this process over the phone, via email, and PM's. I've posted the process on at least 3 occasions. Here it is again in a nutshell: 1. Using the EO/IC method, get the lifter to the base circle of the cam. 2. Using a known length pushrod (7.400" is a good start with stock rockers) run the rocker arm bolt down to zero lash. This is easily done with your fingers "wiggling" the rocker, the point at which the "slack" is just gone is zero lash. 3. Set your torque wrench to 22 lb./ft. Tighten the rocker to full torque and count the number of turns it takes to get there. 1 full turn wtih a stock 8mm X 1.25 bolt is ~.047" preload as measured at the pushrod/rocker interface. 4. I normally shoot for 1 1/4 to 1 3/4 turns with stock type lifters like Comp 850's, LS1, LS7 etc. For an example, if you use a 7.400" pushrod and come up with 3/4 of a turn, you will need at least .025" longer pushrod to get into range. If you end up with 2 1/4 turns, you will need one .025" shorter... I might not know everything but I will tell you that this method has worked for me year after year cam swap after cam swap. We average 3 cam swaps a week here so you can do the math. If you are not familiar with the EO/IC method for determining valve events in a 4 stroke engine, its very simple: For a given cylinder as the Exhaust valve is Opening, the intake lifter will be on the base circle of the cam and lash/preload should be checked for that intake valve. For a given cylinder as the Intake valve is Closing, the exhaust lifter will be on the base circle of the cam and lash/preload should be checked for that exhaust valve. THIS METHOD ALWAYS WORKS!!! Check it using the above method and see where you are. Thanks, Shane |
they say one turn is .047 but its funny cause when setting a given amount of preload in the checker the bolt method doesnt match
|
One turn is not .o47 or .060.
I prefer 1 full turn which is near .080". |
thats what i found, .075 of preload added to the checker was 1 full turn.
|
i will break out the digital torque wrench and set it to torque angle when my new pushrods come in and find out the exact degrees vs preload.
|
Well then I guess I have too much pre load? If 1 turn is .080 then I am damn near .120. I will check it again this week after work.
|
yeah i agree. 1 turn is around .080 and your target. loser is ok on a high rpm all the time engine. but for stock-ish .085 is GM's spec. on a sied note i run mt LS7 lifters at .040 pre load (1/2 turn) and there is no noise.
|
| All times are GMT. The time now is 05:06 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.