|
#11
|
||||
|
||||
|
me mentioned that to me and also a fuse for the engine sensor. I was getting 75 miles to 3/4 of a tank so i knew something had to be off.
__________________
![]() 06 CTSV 08 Spec B Sold 00 Yukon SLT Sold 05 STI Sold 02 WS6 Sold 12/1/12 94 1LE Sold 3/18/11 02 WRX Sold 2/18/12 Drag racing a car thats been totaled is like fucking a hooker with no rubber. Either way your a stupid fuck. |
|
#12
|
||||
|
||||
|
Mine isn't much better is it a regular fuse or relay?? U have a check engine light on???
__________________
![]() 1999 Camaro SS480 http://www.youtube.com/watch?v=hGXXuq9T2TI G,M. Precision Welding and Fabrication GMPrecisionWelding@gmail.com |
|
#13
|
|||
|
|||
|
Quote:
exactly what happened when i did my header install on my camaro and the guy who did them wired the O2s wrong...i was getting like 5 mpg....Don went to tune it did a pull then hopped under the car and rewired them for me. and all problems were solved
__________________
-Mike ![]() 94 Mustang GT - BBK Shorty Headers, H pipe, Flowmasters, 3.73s, UD pulley, 4 point brace SOLD - 2000 Trans Am WS6 - M6//F13 Cam//Pacesetter LTs//Catted Y//Magnaflow CB//LS7 Clutch//K&N//P+P LS6 intake//1.6 RR//Slowhawk Tune SOLD - 02 Z28 - A4//SLP Lid//SLP SB//STB//Pacesetter LTs//TSP ORY//Magnaflow//Ported TB//EBC Dimpled & Slotted Rotors// 12.96 @ 107 |
|
#14
|
||||
|
||||
|
I only replaced one last year the other one was ok so i'm going to get another today and see if it helps but its just not running correct i can tell. when i'm driving it and i push in the clutch it stays at the rpms it was at say like 2 grand and sits there a few seconds and eventually falls back down to idle i dont like how its doing that. Something is up i'm sure. hopefully thats the issue. I checked the fuse that was ok
__________________
![]() 1999 Camaro SS480 http://www.youtube.com/watch?v=hGXXuq9T2TI G,M. Precision Welding and Fabrication GMPrecisionWelding@gmail.com |
|
#15
|
|||
|
|||
|
Quote:
__________________
-Mike ![]() 94 Mustang GT - BBK Shorty Headers, H pipe, Flowmasters, 3.73s, UD pulley, 4 point brace SOLD - 2000 Trans Am WS6 - M6//F13 Cam//Pacesetter LTs//Catted Y//Magnaflow CB//LS7 Clutch//K&N//P+P LS6 intake//1.6 RR//Slowhawk Tune SOLD - 02 Z28 - A4//SLP Lid//SLP SB//STB//Pacesetter LTs//TSP ORY//Magnaflow//Ported TB//EBC Dimpled & Slotted Rotors// 12.96 @ 107 |
|
#16
|
||||
|
||||
|
Just FYI I moved these posts from the Quabbin thread so it could be in a tech related section
|
|
#17
|
||||
|
||||
|
It never used to do it. like at the track i do my burnout and then it stays reved high up and i sit for like seconds to get it to calm back down to idle its really strange but the new O2 didnt do it. so next option maybe i need a new MAF
__________________
![]() 1999 Camaro SS480 http://www.youtube.com/watch?v=hGXXuq9T2TI G,M. Precision Welding and Fabrication GMPrecisionWelding@gmail.com |
|
#18
|
||||
|
||||
|
sounds like a vaccum leak to me.
__________________
![]() 1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. ![]() BAAAAAA!!!!!! |
|
#19
|
||||
|
||||
|
Yeah I'm pretty sure I've read some threads on LS1Tech about stuff like that and it was usually a vacuum leak. Check your PCV line, they are known to crack on LS1s.
|
|
#20
|
||||
|
||||
|
checked the hoses look new. Its gotten a little better i think. I took the maf apart and cleaned it really well and i'm hoping the pcm re learns it. cause this gas mileage is annoying it shouldnt be this bad. My 69 camaro isnt even as bad as my LS right now
__________________
![]() 1999 Camaro SS480 http://www.youtube.com/watch?v=hGXXuq9T2TI G,M. Precision Welding and Fabrication GMPrecisionWelding@gmail.com |
![]() |
|
|